Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 107 / 1000

3. Tighten the accessory drive belt idler pulley bolt.

Tighten:

Tighten the accessory drive belt idler pulley bolt to 50 N.m (37 lb ft).

DRIVE BELT IDLER PULLEY REPLACEMENT - AIR CONDITIONING

Removal Procedure

Fig. 7: A/C Drive Belt Idler Pulley

Courtesy of GENERAL MOTORS CORP.

1. Loosen the air conditioning (A/C) drive belt idler pulley bolt.

2. Remove the A/C drive belt. Refer to

Drive Belt Replacement - Air Conditioning

3. Remove the A/C drive belt idler pulley.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:32 AM

Page 7

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands