Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 244

Page: 244 / 1000

Fig. 136: View Of Spark Plug

Courtesy of GENERAL MOTORS CORP.

3. Loosen the spark plug 1 or 2 turns.

4. Brush or use compressed air to remove any dirt or debris around the spark plug.

5. Remove the spark plug.

IMPORTANT: Remove the spark plugs from the cylinder head with the engine at room

temperature.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:38 AM

Page 144

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands