manualshive.com logo in svg

Chevrolet 5.7L Corvette 2004, Shop Manual

Share
Download
Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 64

DRIVE BELT SQUEAL DIAGNOSIS 

Diagnostic Aids 

A loose or improper installation of a body, or suspension component, or other item(s) on the vehicle may cause 
the squeal noise. 

If the noise is intermittent, verify that the accessory drive component(s) by varying their loads, making sure 
they are operating to their maximum capacity. An overcharged air conditioning (A/C) system, a power steering 
system restriction, or the incorrect fluid, or a failing generator are suggested items to inspect. 

Test Description 

The number(s) below refer to the step(s) in the diagnostic table. 

2:

 The squeal may not be engine related. This step is to verify that the engine is making the noise. If the 

engine is not making the noise do not proceed further in this table.  

3:

 The noise may be an internal engine noise. Remove the drive belt(s) and operate the engine for a few 

seconds, this will verify if the squealing noise is related to the drive belt(s) or an accessory drive 
component. With the drive belt(s) removed the water pump will not operate and the engine may overheat. 
Also diagnostic trouble codes (DTCs) may set when the engine is operated with the drive belt(s) 
removed.  

4:

 This test is to verify that an accessory drive component(s) does not have a seized bearing. With the belt

(s) removed, test the bearings in the accessory drive components for smooth operation. Also test the 
accessory drive component(s) with the engine operating by varying the load on the accessory drive 
component(s) to verify that the component(s) is operating properly.  

5:

 This test is to verify that the drive belt(s) tensioner(s) is operating properly. If the drive belt(s) 

tensioner(s) is not operating properly, proper belt tension may not be achieved to keep the drive belt from 
slipping which could cause a belt squeal noise.  

6:

 This test is to verify that the drive belt(s) is not too long, which would prevent the drive belt(s) 

13

Replace the bent accessory drive pulley
(s). 
Was the bent accessory drive pulley(s) 
replaced?

Go to 

Step 15

-

14

Replace the drive belt(s). Refer to 

Drive Belt Replacement - Accessory

 

or 

Drive Belt Replacement - Air 

Conditioning

 . 

Was the drive belt(s) replaced?

Go to 

Step 15

-

15

1. Clear any codes  

2. Run the engine in order to verify 

the repair.  

Does the chirping noise still exist?

Go to 

Step 3

System OK

 

2004 Chevrolet Corvette 

2004 ENGINE PERFORMANCE Engine Mechanical (Introduction) - 5.7L - Corvette

  

Helpmelearn 

 

December-24-07 10:50:09 AM

Page 64 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands