Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 319

Page: 319 / 1000

Fig. 202: View Of Crankshaft Rear Oil Seal

Courtesy of GENERAL MOTORS CORP.

1. Lubricate the outside diameter (OD) of the oil seal (1) with clean engine oil.

DO NOT allow oil or other lubricants to contact the seal surface.

2. Lubricate the rear cover oil seal bore with clean engine oil.

DO NOT allow oil or other lubricants to contact the crankshaft surface.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:42 AM

Page 219

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands