manualshive.com logo in svg

Chevrolet 5.7L Corvette 2004, Shop Manual

Share
Download
Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 878

5. Install the camshaft retainer and the bolts. 

Tighten:

 Tighten the camshaft retainer bolts to 25 N.m (18 lb ft). 

6. Inspect the camshaft sensor O-ring seal. If the O-ring seal is not cut or damaged, it may be used again.  

7. Lubricate the O-ring seal with clean engine oil. 

Fig. 59: View Of Camshaft Sensor & Bolt

 

Courtesy of GENERAL MOTORS CORP.

z

The gasket surface on the engine block should be clean and free of 
dirt or debris.  

 

2004 Chevrolet Corvette 

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L - Corvette

  

Helpmelearn 

 

December-24-07 11:06:37 AM

Page 65 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands