Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 460 / 1000

Fig. 336: MAP Sensor Vacuum Hose & MAP Sensor Electrical Connector

Courtesy of GENERAL MOTORS CORP.

27. Install the ground strap (6) and ground strap bolt (5) to the rear of the left cylinder head.

Tighten:

Tighten the ground strap bolt (5) to 32 N.m (24 lb ft).

28. Route the electrical harness and connect the following electrical connectors at the rear of the engine:

The knock sensor wire harness (1)

The engine oil pressure sensor (2)

The MAP sensor (3)

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:50 AM

Page 360

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands