Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 517

Page: 517 / 1000

2004 ENGINE PERFORMANCE

Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

REPAIR INSTRUCTIONS

THROTTLE BODY REMOVAL

Fig. 1: Throttle Body & Bolts

Courtesy of GENERAL MOTORS CORP.

1. Remove the electrical wire harness connectors from the throttle body.

2. Remove the engine coolant air bleed hose and clamp.

IMPORTANT: The intake manifold, throttle body, fuel injection rail and fuel injectors

may be removed as an assembly. If not servicing the individual
components, remove the manifold as a complete assembly.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:09 AM

Page 1

Helpmelearn

December-24-07 11:03:33 AM

Page 1

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands