Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 603 / 1000

10. Remove the engine block front oil gallery plug.

ENGINE BLOCK CLEANING AND INSPECTION

Tools Required

J 8087

Cylinder Bore Gage

J 42385-100

Head/Main Bolt Thread Repair Kit

1. Clean the following areas:

The engine block in the solvent

Remove all sludge, dirt, or debris. Refer to

Cleanliness and Care

Dry the block with compressed air.

The gasket surfaces

Refer to

Replacing Engine Gaskets

The coolant passages

The oil galleries

The main bearing caps

The engine block head bolt holes for threadlocking material

Thread repair tool J 42385-107 may be used to clean the threads of old threadlocking material.

2. Inspect the following areas:

The cylinder walls for excessive scratches, gouging, or ring ridge

The coolant jacket for cracks

The valve lifter bores for excessive scoring or wear

The crankshaft bearing webs for cracks

be installed.

NOTE:

Do not use a caustic solution to clean the aluminum engine block.

IMPORTANT: When cleaning an engine block in a thermal type oven, do not

exceed 232°C (450°F).

CAUTION: Refer to Safety Glasses Caution in Cautions and Notices.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:13 AM

Page 87

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands