Carrier i-Vu CCN Pro 4.2 Installation Manual Download Page 23

Page: 23 / 104

Operating i-Vu CCN Pro

i-Vu CCN Pro 4.2

Proceed to

Scan

Exit System Setup

NOTE Right-click to use drop-down menu or use toolbar to rename, move, copy, or delete areas.

Scan for devices

Scan whenever

•

Equipment is added

•

A specific equipment configuration has been altered

To scan devices and discover their tables

Click the menu button

, then select

System Setup

, if you are not already there.

In the navigation tree, select the desired area. As devices are discovered, they will appear in the tree

under the highlighted area. The tree can be manipulated later by dragging or using the arrows on the left

toolbar.

To start scanning, enter the applicable

Bus

and

Element

numbers of a specific device or for a range of

devices.

Verify that

Discover Tables

is checked.

NOTE

The scanning time for discovering tables increases based on the number of devices. You may

choose to discover tables at a later time for a faster scan.

Click

Start Scan

. When the process is complete, a message appears showing the number of equipment

found.

NOTE If there is a missing gateway, the message will appear, "You must discover a device before adding

an equipment."

Update library and change addressing

Update Library -

The Library holds graphics and definitions for CCN devices. This link allows you to update

your Library when you are notified that Carrier has new graphics available. After you have downloaded and

saved the graphic to your computer, use this option to upload to your i-Vu CCN Pro. Be sure to re-scan the

applicable piece of equipment after updating the Library.

Change Addressing -

Enter new

Element

and

Bus

number to change the physical address of a device.

Re-scan or download equipment

Whenever a piece of equipment is changed or a specific equipment configuration has been altered:

Highlight the device or devices (CTRL-click) in the

System Setup

table.

Verify that

Discover Tables

is checked.

Click

Start Scan

If download has failed:

Summary of Contents for i-Vu CCN Pro 4.2









































































































Search results

Summary of Contents for i-Vu CCN Pro 4.2

Reviews:

Related manuals for i-Vu CCN Pro 4.2

Brands by name

Popular brands

Carrier i-Vu CCN Pro 4.2, Installation Manual

Search results

Summary of Contents for i-Vu CCN Pro 4.2

Reviews:

Related manuals for i-Vu CCN Pro 4.2

Brands by name

Popular brands