Canon MultiPASS L60 User Manual Download Page 79 | Manualshive

Page: 79 / 341

Canon MultiPASS L60 User Manual Download Page 79

Chapter 3

Registering Information in the MultiPASS L60

3-7

Registering

Information in the

MultiPASS L60

Using the One-Touch Speed Dial/Special Function
Buttons

The one-touch speed dial/special function buttons allow you to use
speed dialling and special functions such as delayed fax transmission,
printing reports, and sending with a password/subaddress. The

FUNCTION

button switches the buttons’ functions between one-touch

speed dialling and special functions.

Using the Menu System

The MultiPASS L60 includes a menu system under the

FUNCTION

button that allows you to select operation settings, and to enter user
information. The system includes these menus:

❏

TEL REGISTRATION

Lets you register numbers for one-touch speed dialling, coded speed
dialling, and group dialling.

❏

USER SETTINGS

Lets you enter the information that prints on the faxes you send, to
set scanning contrast, and to enter other basic data. Enter these
settings when you plug your unit in for the first time; you will rarely
need to change them thereafter.

«
...
77
78
79
80
81
...
»

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments