manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 146 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 146

6-18

Sending Faxes

Chapter 6

Sending Documents

This section describes the different ways to send faxes with the 
MultiPASS L60.

Manual Sending Via the Handset

If you have the optional handset or a telephone connected to your 
MultiPASS L60, you can send faxes manually. This allows you to talk to
the other party before sending the fax, which can be useful if the other
party uses a single line for both voice and fax transmissions.

N

Be sure to adjust the document feed lever before loading your
document. See page 6-6 for details.

1.

Prepare the document and load it, face down, into the Automatic
Document Feeder (ADF).

❏

Once the document is loaded, the LCD display shows the
following:

Currently used memory:

Current resolution:

Standby to scan:

❏

If necessary, you can adjust the resolution and contrast. See
page 6-13 for details.

2.

Lift the handset and dial the number

Ex:  

❏

Use one of the dialling methods described on page 6-17.

TEL=  2 887 0166

LINE IN USE

DOCUMENT READY

STANDARD

MEMORY USED   0%

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments