manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 142 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 142

6-14

Sending Faxes

Chapter 6

Setting the Scanning Contrast

Contrast is the difference in brightness between the lightest and darkest
parts of a printed document. You can adjust the contrast the MultiPASS
L60 uses when scanning documents to be sent. STANDARD is the
default setting and is adequate for most documents. To darken a light
original, set to DARKER; to lighten dark originals, use LIGHTER.

N

You can also set the scanning contrast from the MultiPASS Desktop
Manager. For details, refer to the MultiPASS Desktop Manager 

User’s

Guide

.

1.

Press 

FUNCTION

.

2.

Use 

<

<

or 

>

>

to select USER SETTINGS.

3.

Press 

START/COPY

, then use 

<

<

or 

>

>

to select SCAN CONTRAST.

4.

Press 

START/COPY

.

❏

The currently set scanning contrast is displayed.

STANDARD

SCAN CONTRAST

USER SETTINGS

FUNCTION

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments