manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 145 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 145

Chapter 6

Sending Faxes

6-17

Sending Faxes

Dialling Methods

There are several ways of dialling the number of the party you want to
send to:

❏

Regular dialling

Use the numeric buttons to dial the recipient’s fax number.

❏

One-touch speed dialling

Press the one-touch speed dialling button (1 to 16) under which you
have registered the number you want to send to. See Chapter 5
“Speed Dialling” for details on registering and using one-touch
speed dialling.

❏

Coded speed dialling

Press 

CODED DIAL

and enter the two-digit code (00 to 99) under

which you have registered the number you want to sent to. See
Chapter 5 “Speed Dialling” for details on registering and using
coded speed dialling.

❏

PC Dialling

Dial a fax number from your PC using the MultiPASS Desktop
Manager. See the  MultiPASS Desktop Manager 

User’s Guide

for

details.

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments