manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 270 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 270

12-6

Maintaining Your MultiPASS L60

Chapter 12

Cleaning the Scanner Components

Periodically check the scanning glass and rollers.

N

When you unplug the unit, any faxes stored in memory will be erased.
Be sure to print out any documents received in memory before
unplugging the unit. See pages 7-17 and 7-18.

1.

Unplug the MultiPASS L60.

2.

Open the operation panel.

3. Use a soft, dry clean cloth to clean the scanning glass and rollers

(shaded areas).

❏

If the document scanning glass and rollers are dirty, the
documents you send or print will also be dirty.

❏

Clean with a soft cloth that will not scratch the glass or rollers.

SCANNING
GLASS

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments