manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 58 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 58

2-26

Setting Up Your MultiPASS L60

Chapter 2

❏

D.T. button   05

Press this button to confirm the dial tone when dialling a number.
(Not used in the UK, Hong Kong, Australia, New Zealand,
Singapore, or Malaysia.) See page 8-5 for details.

❏

TONE/+ button   09

Press this button to use tone dialling temporarily when your unit is
set for pulse dialling. See page 8-6 for details. Press also to enter a +
sign when registering your fax/telephone number.

❏

<

<

, 

>

>

(Arrow) buttons   10 and 12

Use these buttons to scroll through menu selections or to move the
cursor when registering data.

❏

R button   16

Press this button to dial an outside line access number when the unit
is connected through a switchboard (PBX). See page 8-2 for details.

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments