manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 121 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 121

Chapter 5

Speed Dialling

5-17

Speed Dialling

Using Coded Speed Dialling

Once you have registered your numbers under coded speed dialling
codes, you can send documents as follows:

N

Be sure to adjust the document feed lever before loading your
document. See page 6-6 for more details.

1.

Prepare the document and load it, face down, into the Automatic
Document Feeder (ADF).

❏

If necessary, you can adjust the resolution and contrast. See
page 6-13 for more details.

2.

Press 

CODED DIAL

.

3.

Use the numeric buttons to enter the two-digit code assigned to the
fax number. 

❏

The name registered under that coded speed dialling code is
displayed. If no name is registered, the number registered
under that code will be displayed.

❏

If you mistakenly enter the wrong code, press the 

STOP

button. Then press the 

CODED DIAL

button and enter the

correct code.

❏

If no fax number is assigned to the coded speed dialling code
you press, the LCD displays NO TEL #. If this happens, make
sure you entered the correct code and that the number you
want to dial is registered under that code.

TEL=CANON U.S.A

✱

03

✱

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments