manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 103 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 103

Chapter 4

Paper Handling

4-17

Paper Handling

Your MultiPASS L60 is now ready to print. 

N

❏

If you insert a sheet into the manual feed slot when there is paper
stacked in the multi-purpose tray, the unit will feed the sheet from
the manual feed slot.

❏

Insert a sheet in the manual feed slot only when the previous sheet
has come out from the delivery slot. If you insert a single sheet
before the previous one has come out, a paper jam may occur.

❏

If you have difficulty feeding certain types of paper through the
manual feed slot, try feeding it through the multi-purpose tray. To
do this, temporarily remove any paper from the multi-purpose tray
and feed through it the paper you are having difficulty with.

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments