manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 31 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 31

Introducing the

MultiPASS L60

Chapter 1

Introducing the MultiPASS L60

1-17

C

Unplug the MultiPASS L60 and contact your local authorised Canon
dealer or the Canon help line in any of these situations:

❏

If the power cord or plug is damaged or frayed.

❏

If liquid spills into the unit, or if it is otherwise exposed to rain or
liquids.

❏

If you notice smoke or unusual noises or odour coming from it.

❏

If the MultiPASS L60 does not operate normally when you follow
the operating instructions. Adjust only those controls that are
covered by the operating instructions in this user’s guide, or you can
damage the unit and require extensive repair work.

❏

If the MultiPASS L60 is dropped or its cabinet damaged.

❏

If the MultiPASS L60 begins performing poorly, and you cannot
correct the problem by following the procedures in Chapter 11,
“Frequently Asked Questions”.

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments