manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 177 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 177

Chapter 6

Sending Faxes

6-49

Sending Faxes

Registering Speed Dialling With the M Button

When registering numbers for one-touch or coded speed dialling, you
can also register your access code and ID code. This allows you to send
documents or make calls over the 2300 Service of Mercury
Communications Limited at the press of one or a few buttons. 

N

You must first register the access code and ID code under the 

M

button

before you can register them under speed dialling numbers.

1.

While you are registering a number for one-touch or coded speed
dialling, and you come to a step that asks you to enter the number
of the other party, press 

FUNCTION

, then press 

M

.

2.

Use the numeric buttons to enter the number.

Ex:  

3.

Continue with the procedure for registering one-touch or coded
speed dialling numbers.

Once you have registered the 

M

button with the numbers under speed

dialling numbers, you can dial and use the 2300 Service without
pressing the 

M

button.

TEL=   M773 3173

TEL=           M

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments