manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 213 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 213

Chapter 10

Reports and Lists

10-1

Repor

ts and Lists

Chapter 10

Reports and Lists

This chapter describes how to print reports and lists. These include
activity reports (transmission and reception reports), lists of registered
numbers, list of user’s data registered in the MultiPASS L60 and the
memory clear report.

❏

Activity Report .................................................................................. 10-2

❏

Transmission (TX) Reports .............................................................. 10-3
• Error TX Report ............................................................................ 10-3
• TX Report ...................................................................................... 10-4
• Multi TX/RX Report .................................................................... 10-5

❏

Reception (RX) Report ...................................................................... 10-6

❏

Memory Clear Report ...................................................................... 10-7

❏

User’s Data List ................................................................................ 10-8

❏

Speed Dialling Lists .......................................................................... 10-10
• One-Touch Speed Dial List.......................................................... 10-11
• Coded Speed Dial List ................................................................ 10-11
• Group Dial List ............................................................................ 10-11

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments