manualshive.com logo in svg

Canon MultiPASS L60, User Manual, Page: 229 / 341

Share
Download
Canon MultiPASS L60 User Manual Download Page 229

Chapter 11

Frequently Asked Questions

11-5

Fr

equently Asked

Questions

Paper Jams

On occasion, the document feeding into the MultiPASS L60 Automatic
Document Feeder (ADF) or the paper in its multi-purpose tray may
misfeed or jam. If this happens, you can usually fix the problem using
one of the following procedures.

N

You do not need to unplug the MultiPASS L60 while clearing paper
jams.

Jams in the Automatic Document Feeder (ADF)?

Use this procedure if the document in the MultiPASS L60’s Automatic
Document Feeder (ADF) jams or misfeeds. (If this occurs, the message
CHECK DOCUMENT appears in the display.)

1.

Press 

STOP

.

N

Do not try to pull the document out without opening the operation
panel, or you may tear or smudge the document.

2.

Open the operation panel by gently pulling it towards you.

Summary of Contents for MultiPASS L60






















































































































































































































































































































































Reviews:

No comments