Canon Finisher-AK1, Service Manual

Page: 183 / 374

5
5
5-12
5-12
Adjustment > Adjustment at Time of Parts Replacement > Outline
Adjustment > Adjustment at Time of Parts Replacement > Outline
Adjustment at Time of Parts Replacement
Outline
CAUTION: Setting the Dip Switch
If setting the Dip Switch, the Delivery Tray setting on the host machine side returns to
the default.
After setting the Dip Switch, it is necessary to execute the Delivery Tray setting on the
host machine side again.
Except for some items, the adjustment and setting can input from the both devices of the host
machine (service mode) and the finisher (Dip switch).
The input value is memorized in the EEPROM of finisher controller. Regardless of the input
device (host machine or finisher), the setting range and unit are same, and the final input
value is effective.
Item
Bit setting of DSW1
in the finisher
controller PCB
Service mode Range Default Reference
Bufferless Mode ON:1, 3, 8 SORTER> OPTION
>BUFFSW
0 to 4 0 p. 5-53
Adjustment in the Case
of Failure in Stacking
Performance of Tray
(upper curl)
ON:1, 3, 6, 7 SORTER>OPTION
>CURLSW
0 to 2 0 p. 5-54
Adjustment in the Case
of Failure in Stacking
Performance of Tray
(lower curl)
ON:1, 3, 6, 7 SORTER>OPTION
>CURLSW
0 to 2 0 p. 5-56
Adjustment in the Case
of Failure in Stacking
Performance of Tray
(runon of paper when
using thin paper)
ON:1, 3, 7 SORTER>OPTION
>TRYEJCT
0 to 1 0 p. 5-58
Adjustment in the Case
of Canceling Limit for
Tray Stack
ON:1, 3, 5 SORTER>OPTION
>TRYOVER
0 to 1 0 p. 5-60
Setting of Pressless
Mode
ON:1, 3, 4 SORTER>OPTION
>SDLPRS
0 to 3 0 p. 5-120
T-5-4
When replacing the parts shown below, perform the appropriate adjustment.
Adjustment Type Symptom, adjustment timing Reference
Adjusting Sensor Light
Intensity
When replacing a sensor p. 5-14
Adjusting Position of
Tray A, B
When replacing the Tray A/B Unit p. 5-16
Adjusting the Alignment
Position of the Upper
Neat Alignment Plate
When replacing or installing/removing the Neat Stack
Unit (Upper) and the component parts of the unit
When replacing the Finisher Controller PCB
p. 5-17
Adjusting the Alignment
Position of the Lower
Neat Alignment Plate
When replacing or installing/removing the Neat Stack
Unit (Lower) and the component parts of the unit
When replacing the Finisher Controller PCB
p. 5-19
Adjusting the Height of
Corrugation Roller for
Stack Delivery
When replacing the Finisher Controller PCB p. 5-21
Right Angle Adjustment
of Alignment Plate
• When replacing the Front Alignment Motor
• When replacing the Rear Alignment Motor
p. 5-25
Adjusting Alignment
Plate Position
• When replacing the Front Alignment Motor
• When replacing the Rear Alignment Motor
• When replacing the Finisher Controller PCB
p. 5-26
Adjusting Position of
Stapler
When replacing the Stapler p. 5-28
Adjusting Staple
Position (1-stapling at
the rear)
When replacing the Finisher Controller PCB p. 5-29
Adjusting Staple
Position (1-stapling at
the front)
p. 5-32
Adjusting Staple
Position (2-stapling
positions)
p. 5-35
Adjusting Delivery of
Staple Stack (lower
delivery)
p. 5-37
Adjusting Delivery of
Staple Stack (saddle
delivery)
p. 5-40
Saddle Stitch/Fold
Placement Adjustment
p. 5-43