Baumuller BM5-O-SAF-002 Operation Manual Download Page 4

Page: 4 / 182

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

of 180

Inhaltsverzeichnis

7.5.2

Acknowledgment encoder fail status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7.6

The Structure of the Safety Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

7.7

Processing and Display Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

7.7.1

LEDs for the Display of Operating States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

7.7.2

Button for verification reasons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

7.8

Software Extension SAF-002/-003 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

7.9

Identification of the Safety Module - Type Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

8 Description of the Reset-Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

8.1

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

8.2

Compatibility list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

8.3

Operating mode of the Reset-Module (BM5-O-SAF-100) . . . . . . . . . . . . . . . . . . . . . . 49

8.4

Structure of the Reset-Module (BM5-O-SAF-100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

8.5

Identification of the Reset-Module (BM5-O-SAF-100) . . . . . . . . . . . . . . . . . . . . . . . . . 50

8.6

Mode of operation module replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

9 Resetting of the safety level by the controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

9.1

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

9.2

Operation of mode of the reset command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

10 Safety Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

10.1

Safety Functions of the Module BM5-O-SAF-002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

10.2

Safety Functions of the Module BM5-O-SAF-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

10.3

Safe Torque Off (STO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

10.3.1

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

10.3.2

Safety notes for the Function STO (Safe Torque Off) . . . . . . . . . . . . . . . . . . . . . . . . 58

10.4

Safe Stop 1 (SS1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

10.4.1

Signalize SS1-start to the controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

10.4.2

Error reaction for the safety function „SS1“ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

10.5

Safe Stop 2 (SS2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

10.5.1

Error reaction with function-specific SS1 time for the safety function "SS2" and its follow-

ing function "SOS" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

10.6

Safe Operating Stop (SOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

10.6.1

Error reaction with function-specific SS1 time for the safety function "SOS". . . . . . . 66

10.7

Safely Limited Speed (SLS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

10.7.1

Error reaction with a function-specific SS1 time for the safety function "SLS". . . . . . 69

10.8

Safe Direction (SDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

10.8.1

Error reaction with function-specific SS1 time for the safety function "SDI" . . . . . . . 71

10.9

Safe Brake Control (SBC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

10.9.1

Error reaction with a function-specific SS1 time for the safety function "SBC" . . . . . 74

10.10

Safely Limited Position (SLP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

10.10.1

Error reaction with function-specific SS1 time for the safety function "SLP" . . . . . . . 77

10.11

Safely Limited Increment (SLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

10.11.1

Error reaction with function specific SS1 time for the Safety function "SLI" and the follow-

ing function "SOS" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

10.11.2

Operating principle of SLI and description of the transition SLI ->STO . . . . . . . . . . . 79

10.12

Safely Limited Acceleration (SLA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

10.12.1

Error reaction with function-specific SS1 time for the safety function "SLA" . . . . . . . 82

10.13

Safe Speed Monitor (SSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

10.13.1

Error reaction with function-specific SS1 time for the safety function "SSM". . . . . . . 84

10.14

Safe Cam (SCA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

10.14.1

Error reaction with function-specific SS1 time for the safety function "SCA" . . . . . . . 86

10.15

Tolerance for the limit values of the safety functions . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Summary of Contents for BM5-O-SAF-002























































































































































































Search results

Summary of Contents for BM5-O-SAF-002

Reviews:

Baumuller BM5-O-SAF-002, Operation Manual, Page: 4 / 182

Search results

Summary of Contents for BM5-O-SAF-002

Reviews: