Baumuller BM5-O-SAF-002 Operation Manual Download Page 177

Page: 177 / 182

EC - Declaration of Conformity

Doc.-No.

5.12065.01



Date:

09/13/2018

according to EMC Directive 2014/30/EU

The Manufacturer:

Baumüller Nürnberg GmbH



Ostendstraße 80-90



90482 Nürnberg, Germany

declares, that the products:

Designation:

b maXX 5000 option module with safety functions



Type:

BM5-O-SAF-002 and BM5-O-SAF-003



manufactured since:

10/02/2018

are developed, designed and manufactured in accordance with the EMC Directive 2014/30/EU.

Applied harmonised standards:

Attention should be paid to the safety instructions in the manual.

Nuremberg / 09/13/2018

Location / Date

Subject to change of this declaration of EC conformity without notice. Actual valid edition on request.

Standard

Title

IEC 61800-3:2017

Adjustable speed electrical power drive systems



Part 3: EMC requirements and specific test methods

Declaration of conformity

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

177

of 180

Summary of Contents for BM5-O-SAF-002























































































































































































Search results

Summary of Contents for BM5-O-SAF-002

Reviews:

Baumuller BM5-O-SAF-002, Operation Manual, Page: 177 / 182

Search results

Summary of Contents for BM5-O-SAF-002

Reviews: