manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 30 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 30

Disposing of the packaging

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

30

of 180

6.3

If no damage from shipping can be found:

h

Open the packaging of the device.

h

Check the items included in the delivery against the bill of delivery.

The items included in the delivery are:

m

Safety Module for b maXX 5000

, BM5-O-SAF-002 or BM5-O-SAF-003

m

This operation manual including certificate of conformity / declaration of manufacturer.

h

If any shipping damages can be found or any items are missing from the delivery, file 
a complaint to the Baumüller representative assigned to you.

6.3

Disposing of the packaging

The packaging consists of cardboard and plastic.

h

Follow local regulations on disposal if you dispose of the packaging.

6.4

To be observed when shipping

The module has been packaged at the factory for the initial shipping. If you subsequently 
need to ship the module again, observe the following:

h

Use the original packaging

or

h

Use suitable packaging for the components groups which are sensitive to electrostatic 
discharge.

Make sure that the shipping conditions (see 

Z

Appendix C - Technical data

– 

from page 

163 onward) are consistently fulfilled throughout the entire shipping process.

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments