manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 164 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 164

Technical Data safe inputs, STO-Inputs and Daisy-Chain-Inputs

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

164

of 180

C.2

C.2.1

Technical data Daisy-Chain-Outputs

Rated output voltage

24 V

Rated output current

50 mA

Proof voltage

60 V

Output type

protected output according to EN 61131-2

Test pulse length: 800 µs (always active)

C.2.2

Technical data safe outputs

Rated output voltage

24 V

Rated output current

500 mA

Required minimum current

50 mA

Proof voltage

60 V

Output type

protected output according to EN 61131-2.

Test pulse length: 800 µs (always active)

C.2.3

Technical data cycle outputs

Rated output voltage

24 V

Rated output current

50 mA

Output type

protected output according to EN 61131-2.

Test pulse length: 800 µs (active, if at least one input was parameterized as "Sensor type 
passive").

C.2.4

Technical data power outputs

Rated output voltage

24 V / 48 V 
(for details see Operating Manual b maXX 5000)

Rated output current 

4 A

Proof voltage

60 V

Output type

protected output according to EN 61131-2.

Test pulse length: 2800 µs (always active)

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments