Baumuller BM5-O-SAF-002 Operation Manual Download Page 141

Page: 141 / 182

Troubleshooting and Error Correction

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

141

of 180

Invalid instance for parameters

yes

Invalid data set for parameters

yes

Invalid parameter access

yes

Run-time error for safe cycle

Invalid mode to delete the flash

Time exceeding when reading the analog values

Programming or deleting of flash is already activated

Invalid encoder signal

Invalid encoder type

yes

Time exceeding when reading ProSafePara file

Time exceeding at cross monitoring

Invalid ProSafePara file

yes

Invalid telegram for cross communication

Invalid start character for cross communication

Invalid telegram type for cross communication

Invalid telegram length for cross communication

Telegram repetition at cross communication

CRC error cross communication

Interface for cross communication is already in use

Time exceeding at cross communication

Online test wasn’t synchronized

yes

Online test already active

Error at online test

yes

No data exchange at FSE communication

No new FSoE data from the master

Incorrect identification for GDP real time telegram

yes

Incorrect command for GDP real time telegram

yes

Incorrect telegram length for GDP real time telegram

yes

Incorrect list parameter for GDP real time telegram

yes

Incorrect checksum for GDP real time telegram

yes

No GDP real time configuration was established

yes

Time exceeding for GDP real time telegram update

yes

Different number of axes at the DIP-switch and ProSafePara file

yes

Different number of axes at the DIP-switch and the controller

yes

Error when reading the DIP-switches

yes

No adequate controller for Safety Module

yes

Different versions of Safety Module and ProSafePara file

yes

Parameter check axis 1: Different values were detected in the drive and SAF
module (Motor type/Encoder type/Encoder PPR count)

Parameter check axis 2: Different values were detected in the drive and SAF
module (Motor type/Encoder type/Encoder PPR count)

Error when parameterizing the test manager

yes

Error when initializing the test manager

Error at RAM March C test

Error at RAM Galpat test

Error number

Description

SS1 time
general

Summary of Contents for BM5-O-SAF-002























































































































































































Search results

Summary of Contents for BM5-O-SAF-002

Reviews:

Baumuller BM5-O-SAF-002, Operation Manual, Page: 141 / 182

Search results

Summary of Contents for BM5-O-SAF-002

Reviews: