manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 29 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 29

29

of 180

 Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

6

P

ACKAGING

 

AND

 

SHIPPING

Before shipping, we package every Baumüller device in such a manner that damaging 
occurring during transport is very unlikely.

6.1

Shipping

Modules are packaged at the factory according to the order.

h

Avoid heavy shaking and concussions during shipping.

h

Avoid static discharges on the electronic components of the module.

h

Only remove the module from the protective packaging immediately before assembly.

6.2

Unpacking

Upon receiving the still-packaged module:

h

Check to see if any shipping damages can be found!

If so:

h

Immediately file a complaint to the supplier. Confirm the complaint in writing and 
immediately contact the representative of Baumüller Nürnberg GmbH who is assigned 
to assist you.

CAUTION!

Danger due to electrostatic discharge!

 

The Safety Module (specifically its electronic components) can be damaged or totally 
destroyed if exposed to electrostatic discharges by being touched by hand.

Therefore:

m

Follow the rules and instructions on handling components sensitive to electrostatic 
discharge when handling the Safety Module.

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments