manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 117 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 117

Planning of a safety-oriented control system

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

117

of 180

14

The determination of the required safety class (SIL according to EN 62061 and 
performance level according to EN ISO 13849-1) is carried out in the scope of risk 
assessment for the installation/machine in accordance with EN ISO 12100-1 and 
EN ISO 14121.

14.2 Installation and wiring plan

An installation and wiring plan for the entire safety system is to be developed in the 
planning phase. It contains all system components and its wiring. 

CAUTION!

The applicable standards and guidelines on laying electrical lines must be observed 
when developing the wiring plan.

14.3 Course of the planning phase

The system is planned according to the requirements of the installation or the machine. 
The components, which are available for the automation of the available components are 
described in the Automation Catalog of the company Baumüller Nürnberg GmbH. Here 
information on concepts, PLCs, field busses, motion control, technology blocks, HMIs, 
IPCs and I/Os is available.

Prior to commissioning of the Safety Module (SAF-002/-003), the following must be 
checked and guaranteed:

m

Compatibility of the Safety Module (SAF-002/-003) with the controller (see chapter 

Z

Compatibility list

– 

on page 31).

m

Adequate supply of the controller by the connected power supply unit or safety 
components.

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments