manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 15 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 15

15

of 180

 Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

3

U

SE

 

OF

 

THIS

 

MANUAL

This safety manual contains information on the intended use of the Baumüller Safety 
Module.

Knowledge of the regulations and proper technical implementation of the safety 
instructions in this manual by qualified personnel are prerequisites for the safe 
installation, commissioning and safety during the operation and maintenance of the 
Baumüller Safety Module. Unqualified interference with the Safety Modules during 
shutdown or use of the safety functions or failure to comply with the instructions of this 
manual can lead to serious personal injury, property damage or environmental harm, for 
which Baumüller assumes no liability. 

Baumüller safety components and systems are developed, manufactured and tested in 
compliance with the applicable safety standards. They may only be used under the 
specified environmental conditions and only in connection with approved external Safety 
Modules. 

The operation manual contains safety instructions, descriptions of the interfaces and 
information on the phases of the product's life cycle:

n

Planning

n

Installation/Assembly

n

Commissioning

n

Validation

n

Operation

n

Modification/Retrofitting

n

Troubleshooting

n

Maintenance/Repair

n

Disassembly

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments