Baumuller BM5-O-SAF-002 Operation Manual Download Page 65 | Manualshive

Page: 65 / 182

Baumuller BM5-O-SAF-002 Operation Manual Download Page 65

Safety Functions

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

65

10

10.6 Safe Operating Stop (SOS)

NOTE!

The safety function SOS is supported by the Safety Modules SAF-002 and SAF-003.

The safety function „Safe Operating Stop (SOS)“ monitors the reached operating stop
position of the drive and avoids the leaving of the operating stop position.

The drive’s operating stop is monitored via a parameterized tolerance window (position
window).

NOTE!

The ProSafePara parameter ""+/- tolerance for standstill (s_Zero_SOS)" was limited
from ProSafePara V1.1.0.0 to a value of 1073676287 to avoid the exceeding of the
number range by differential generation and in dependence of the encoder triggering
which theoretically is possible (prior limit value: 4294967295).

This new limit applies to the tolerance inputs of "s_Zero_SOS" in all of the "SOS
following functions.

The setting of greater values of earlier ProSafePara versions can lead to availability
issues (immediate STO status after activation).

«
...
63
64
65
66
67
...
»

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments