background image

Installing IP500/IP500 V2

Page 22

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

1.6 IP500 V2 System Components

The following are the typical components of a system based on an IP500 V2 control unit. 

·

IP Office IP500 V2 System Unit

 

The control unit holds the main configuration and performs the
routing and switching for telephone calls and data traffic. Each
control unit includes 4 slots for optional base cards to support
trunk and phone extension ports. 

·

 

Avaya SD Card

This uniquely numbered dongle is used to validate license
keys entered into the system's configuration to enable
features. A dongle is mandatory for correct system operation
even if no licensed features are being used. IP500 V2 control
units use an Avaya SD card which is slotted into the rear of
the control unit. This card also provides Embedded Voicemail
support and storage for system software files. 

·

IP500 Base Cards

The IP500 V2 control unit has slots for up to 4 IP500 base cards.
These can be used to add ports for analog extensions, digital
extensions, voice compression channels and other resources. 

·

IP500 Digital Station Base Card

·

IP500 Analog Phone Base Card

 

·

IP500 VCM Base Card

 

·

IP500 Legacy Card Carrier

 

·

IP500 4-Port Expansion Base Card

 

·

IP500 TCM8 Base Card

 

·

IP500 ETR6 Base Card

 

·

Unified Communications Module

·

IP500 Trunk Daughter Cards

Many of the IP500 base cards can be fitted with an IP500 daughter
card in order to support various types of trunk connections. 

·

IP500 Analog Trunk Card

·

IP500 Analog Trunk Card V2

 

·

IP500 BRI Trunk Card

 

·

IP500 PRI Trunk Card

 

·

IP500 Combination Cards

 

These card are pre-paired base and daughter cards. They provide
6 digital station ports, 2 analog phone ports, 10 voice compression
channels and either 4 analog trunk ports or 4 BRI channels (2
ports). The trunk daughter card cannot be removed or replaced
with another type.

·

IP500 BRI Combination Card

·

IP500 ATM Combination Card

·

IP500 ATM Combination Card V2

·

IP400 Cards

The IP500 Legacy Carrier base card can be used to allow IP400
trunk cards and IP400 VCM cards from previous IP400 systems to
be reused in an IP500/IP500 V2 control unit.

211

47

26

227

221

232

230

220

231

228

225

29

235

235

237

238

26

224

222

222

30

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews: