Avaya IP500 Installation Manual Download Page 318

Page: 318 / 442

Installing IP500/IP500 V2

Page 318

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

10.11.37 5420

This phone is similar in physical appearance and functions to the 2420. However the 5420 is only supported on IP Office.

5420D

Feature

Detail

Connects via

DS port.

IP Office Release

3.0+

Programmable Buttons

24 (8 buttons x 3 pages)

Headset Socket

Handsfree Speaker/Microphone

Message Waiting Lamp

Display

29 characters x 7 lines.

Supported Add-Ons

EU24*, 201B.

Upgradable Firmware

Standard DCP Phone Keys

SPEAKER

HEADSET

MUTE

VOLUME UP

MESSAGES

HOLD

TRANSFER

VOLUME DOWN

DROP

REDIAL

CONFERENCE

Variant

SAP Code

5420D

Multi-Grey

700339823

5420D (RoHS compliant)

Multi-Grey

700381627

Replacement Handset

Dark Grey

700203797

Amplified Handset

Dark Grey

700229735

Noisy Location Handset

Dark Grey

700229743

Push to Talk Handset

Dark Grey

700229727

201B Recorder Interface Module

700381635

20B Stand

700381650

EU24*

Multi-Grey

700381817

1151D1 Power Supply

With CAT5 cable.

700434897

1151D2 Power Supply with battery backup.

With CAT5 cable.

700434905

1151D1/1151D2 Power Cord

USA

405362641

Europe

407786623

Australia/New
Zealand

407786631

India

407790991

United Kingdom

407786599

Argentina

408161453

*When used with an EU24 unit, a 1151 type power supply unit must be used to power the phone.

Summary of Contents for IP500



























































































































































































































































































































































































































































Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands

Avaya IP500, Installation Manual

Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands