manualshive.com logo in svg

Avaya IP500, Installation Manual

Share
Download
Avaya IP500 Installation Manual Download Page 111

Installing IP500/IP500 V2

Page 111

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Initial Configuration Using IP Office Manager: Disable Unused Trunks

·

T1, T1 PRI and E1R2 Trunks 
To disable the whole trunk, on the main form set the Admin option to Out of Service. Otherwise select the
Channels tab and set those channels that are not used to Out of Service. 

·

For T1 set the Type to Out of Service.

·

For T1 PRI set the Admin field to Out of Service.

·

For E1R2 trunks set the Line Signalling Type to Out of Service.

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands