manualshive.com logo in svg

Avaya IP500, Installation Manual

Share
Download
Avaya IP500 Installation Manual Download Page 123

Installing IP500/IP500 V2

Page 123

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

SD Card Management:  

SD Card Folders

The System SD card contains the following folders:

·

/primary 
Contains the firmware files for the IP Office control unit, external expansion modules and
supported phones. The folder can also contain music on hold files and license key files. This is the
main set of files used by the IP Office system when booting up. Also contains the stored copy of
the IP Office configuration. 

·

/backup 
Contains a copy of the primary folder at some previous point. A backup copy of the primary
contents to this folder can be invoked manually (using IP Office Manager or SSA) or as part of the
IP Office software upgrade using IP Office Manager. 

·

/lvmail 
Contains the system prompts used by Embedded Voicemail. Note that the mailbox messages and
greetings are stored in a sub-folder of the /dynamic folder.

·

The sub-folder /AAG is used to store Embedded Voicemail auto-attendant greetings. 

·

/doc 
Contains initial installation documentation for the system. 

·

/dynamic 
Contains files used by the IP Office and retained through a reboot of the IP Office system. 

·

The sub-folder /lvmail is used to store individual user and group mailbox messages, name
recordings and announcements. The storage capacity for Embedded Voicemail is limited to 15
hours regardless of the capacity of the card. 

·

/temp 
Contains temporary files used by the IP Office and not retained through a reboot of the IP Office
system. 

The Optional SD card can contain a similar set of folders. These are used as an additional backup or they can be used as
the source for upgrading the contents of the System SD card. 

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands