manualshive.com logo in svg

Avaya IP500, Installation Manual

Share
Download
Avaya IP500 Installation Manual Download Page 176

Installing IP500/IP500 V2

Page 176

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Polycom Video Module Settings 
The Polycom modules used in the previous example were the Viewstation 128, Viewstation 256 and Viewstation MP.

The Polycom module must have software that supports 'Standard ETSI ISDN' (European ISDN) and have its ISDN Switch
Protocol setting set to 'Standard ETSI Euro-ISDN'

The following were the settings used during testing:

Characteristics

Admin/Software and Hardware/Software

·

Polycom View Station 512 MP.

·

NTSC UIS Interface.

·

View Station PVS 1419.

·

Software: 7.0.1.

·

Network Interface: S/T Interface.

·

ISDN Version: IEUS v18:a00320

Admin/General Setup

Admin/Video Network/ISDN Video Network

·

Country: USA

·

Language: English (USA)

·

Auto Answer: Yes

·

AllowDial: Yes

·

Allow User Setup: Yes

·

Maximum Time on Call: 480.

·

Country Code: 1

·

Area Code: 732

·

Number A: blank

·

Number B: blank

·

ISDN Switch Protocol: Standard ETSI Euro-ISDN.

User Setup

Admin/Video Network/IMUX

·

Auto Answer: Yes

·

PIP: Auto

·

Far Control of Near Camera: Yes

·

MP Mode: Auto

·

Numbers: blank

·

SPID: blank

·

Audio Quality: 168KB/s

·

Advanced Dialing: Dial Channels in Parallel

System Information

Admin/Software and Hardware/Hardware

·

Release: 7.0.1

·

Model: VS: 512

·

Camera: NTSC

·

Video Comm Interface: ISDN_Quad_BRI

·

Network Interface Type: S/T Interface

Admin/Video Network

Admin/Video Network/Call Preference

·

MultiPoint Setup: Auto

·

ISDN Video Calls (H:320): Yes

 

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands