manualshive.com logo in svg

Avaya IP500, Installation Manual

Share
Download
Avaya IP500 Installation Manual Download Page 115

Installing IP500/IP500 V2

Page 115

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Initial Configuration Using IP Office Manager: Setting the Trunk Prefixes

·

BRI, E1 PRI, S0 and QSIG Trunks 

SIP Trunk Prefixes

For IP Office Release 6.0, the prefix fields Prefix, National Prefix, Country Code and International Prefix are
available with the SIP Line settings. These fields are used in the following order: 

1. If an incoming number (called or calling) starts with the + symbol, the + is replaced with the International Prefix

. 

2. If the Country Code has been set and an incoming number begins with that Country Code or with the

International Prefix and Country Code, they are replace with the National Prefix. 

3. If the Country Code has been set and the incoming number does not start with the National Prefix or

International Prefix, the International Prefix is added. 

4. If the incoming number does not begin with either the National Prefix or International Prefix, then the Prefix is

added. 

For example, if the SIP Line is configured with prefixes as follows: 

·

Line Prefix: 9

·

National Prefix: 90

·

International Prefix: 900

·

Country Code: 44

Number Received

Processing

Resulting Number

+441707362200

Following rule 1 above, the + is replace with the International Prefix
(900), resulting in 900441707362200. 

The number now matches the International Prefix (900) and Country
Code (44).Following rule 2 above they are replace with the National
Prefix (90). 

901707362200

00441707362200

Following rule 2 above the International Prefix (900) and the Country
Code (44) are replaced with the National Prefix (90). 

90107362200

441707362200

Following rule 2 above, the Country Code (44) is replace with the
National Prefix (90). 

901707362200

6494770557

Following rule 3 above the the International Prefix (900) is added. 

9006494770557

5.9 DS16B/30B Port Mode Selection

Each IP500 DS16B and IP500 DS30B external expansion module in a system can support either DS phone ports or TCM
phone ports. The modules default to DS phone port operation. The operating mode is set through the system
configuration. 

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands