Avaya IP500 Installation Manual Download Page 294

Page: 294 / 442

Installing IP500/IP500 V2

Page 294

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

10.11.12 3616

This is an 802.11b WiFi phone. It connects to the IP Office via a wireless access point and Avaya Voice Priority Processor
(AVPP).

The availability of

VCM (Voice Compression Module)

channels is necessary to support IP telephony. For IP Office

6.0+, these phones require an

Avaya IP Endpoints

license.

3616

Feature

Detail

Connects via

IP network.

IP Office Release

2.0+

Programmable Buttons

Headset Socket

Message Waiting Lamp

Upgradable Firmware

Variant

SAP Code

3616 Wireless Phone

700413040

Additional battery pack for 3616

700277387

Desktop charger for 3616.

700412901

Clip for 3616

700413057

3616/3626 Configuration Cradle

700375934

406

Summary of Contents for IP500



























































































































































































































































































































































































































































Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands

Avaya IP500, Installation Manual

Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands