Avaya IP500 Installation Manual Download Page 109

Page: 109 / 442

Installing IP500/IP500 V2

Page 109

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Initial Configuration Using IP Office Manager: Extension Numbering

b. Change the Base Extension number to match the user extension who should now be associated with that

extension port by default.

c. Click OK. IP Office Manager will probably give a validation error message due to a user being associated with

two extensions. This can be ignored until all the user moves have been completed.

3. If changing several users repeat the processes as required.

4. Click

to revalidate the configuration and check that no conflicts between users and associated extensions.

5. If the configuration changes are complete, send the configuration back to the IP Office and select appropriate

settings for the reboot.

Summary of Contents for IP500



























































































































































































































































































































































































































































Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands

Avaya IP500, Installation Manual

Search results

Summary of Contents for IP500

Reviews:

Brands by name

Popular brands