manualshive.com logo in svg

Avaya IP500, Installation Manual

Share
Download
Avaya IP500 Installation Manual Download Page 405

Installing IP500/IP500 V2

Page 405

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

System Components: Licences

10.16.3 Trunk Licensing

The following trunks licenses can be used by a IP500/IP500 V2 system. 

·

IP500 Universal PRI (Additional channels) 
These licenses are used to enable additional B-channels above the basic 8 on an IP500 PRI-U card. The IP500 PRI-U
card supports E1, T1 and E1-R2 PRI modes. The IP Office system supports 8 unlicensed B-channels on each IP500
PRI-U port fitted. Additional B-channels, up to the capacity of ports installed and PRI mode selected require
licenses. These additional channels consume licenses based on which additional channels are configured as in-
service from port 9 of slot 1 upwards. D-channels are not affected by licensing. 

·

IPO R9 IP500 T1 ADD 2CH ADI LIC - 275639.

·

IPO R9 IP500 T1 ADD 8CH ADI LIC - 275641.

·

IPO R9 IP500 T1 ADD 22CH ADI LIC - 275640.

·

IPO R9 IP500 E1 ADD 2CH ADI LIC - 275634.

·

IPO R9 IP500 E1 ADD 8CH ADI LIC - 275635.

·

IPO R9 IP500 E1 ADD 22CH ADI LIC - 275633.

·

IPO R9 IP500 E1R2 ADD 2CH ADI LIC - 275637.

·

IPO R9 IP500 E1R2 ADD 8CH ADI LIC - 275638.

·

IPO R9 IP500 E1R2 ADD 22CH ADI LIC - 275636.

·

SIP Trunk Channels 
These licenses are used to configure the maximum number of simultaneous SIP trunk calls supported. The licenses
are consumed by calls in progress on a SIP channel. For SIP support the system also requires 

VCM resources

. 

·

IPO R9 SIP TRNK 1 ADI LIC - 275659. 

·

IPO R9 SIP TRNK 5 ADI LIC - 275660. 

·

IPO R9 SIP TRNK 10 ADI LIC - 275661. 

·

IPO R9 SIP TRNK 20 ADI LIC - 275662. 

·

IP500 Voice Networking 
These licenses are used with the IP500 and IP500 V2 systems to enable support for SCN, QSIG and H323 IP
trunks. For IP Office Release 5, the additional ports license can be used without requiring a base license first. For
voice networking support the system also requires 

VCM resources

.

·

IPO R9 IP500 VCE NTWK 4 ADI LIC - 275642. 

232

232

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands