ARM Cortex-A53 MPCore Technical Reference Manual Download Page 170 | Manualshive

Page: 170 / 635

background image

System Control

ARM DDI 0500D

Copyright © 2013-2014 ARM. All rights reserved.

4-109

ID021414

Non-Confidential

Table 4-100

shows the L2ECTLR_EL1 bit assignments.

To access the L2ECTLR_EL1:

MRS Rt, S3_1_C11_C0_3; Read L2ECTLR_EL1 into Rt
MSR S3_1_C11_C0_3, Rt; Write Rt to L2ECTLR_EL1

4.3.66

L2 Auxiliary Control Register

The L2ACTLR_EL1 characteristics are:

Purpose

Provides configuration and control options for the L2 memory system.

Usage constraints

This register is accessible as follows:

The L2ACTLR_EL1:
•

This register can be written only when the L2 memory system is
idle. ARM recommends that you write to this register after a
powerup reset before the MMU is enabled and before any ACE, CHI
or ACP traffic has begun.

Table 4-100 L2ECTLR_EL1 bit assignments

Bits

Name

Function

[31]

-

Reserved,

RES

0.

[30]

L2 internal asynchronous error

L2 internal asynchronous error caused by L2 RAM double-bit ECC error. The possible
values are:

0

No pending asynchronous error. This is the reset value.

1

An asynchronous error has occurred.

A write of

0

clears this bit and drives

nINTERRIRQ

HIGH. A write of

1

is ignored.

[29]

AXI or CHI asynchronous error

AXI or CHI asynchronous error indication. The possible values are:

0

No pending asynchronous error.

1

An asynchronous error has occurred.

A write of

0

clears this bit and drives

nEXTERRIRQ

HIGH. A write of

1

is ignored.

[28:3]

-

Reserved,

RES

0.

[2:0]

L2 dynamic retention control

L2 dynamic retention control. The possible values are:

0b000

L2 dynamic retention disabled. This is the reset value.

0b001

2 Generic Timer ticks required before retention entry.

0b010

8 Generic Timer ticks required before retention entry.

0b011

32 Generic Timer ticks required before retention entry.

0b100

64 Generic Timer ticks required before retention entry.

0b101

128 Generic Timer ticks required before retention entry.

0b110

256 Generic Timer ticks required before retention entry.

0b111

512 Generic Timer ticks required before retention entry.

EL0

EL1
(NS)

EL1
(S)

EL2

EL3
(SCR.NS = 1)

EL3
(SCR.NS = 0)

-

RW

RW

RW

RW

RW

«
...
168
169
170
171
172
...
»

Summary of Contents for Cortex-A53 MPCore




























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-A53 MPCore

Brand: HQ Pages: 2

Brand: VALMETAL Pages: 38

Brand: Prima Pages: 7

Brand: ARESA Pages: 15

Brand: Dualit Pages: 14

Brand: Kramer Pages: 4

Brand: Mitsubishi Electric Pages: 8

Brand: Mitsubishi Electric Pages: 2

Brand: Mitsubishi Electric Pages: 1

Brand: Kverneland Pages: 54

Chef Tested 785674

Brand: Montgomery Ward Pages: 8

Brand: Hendi Pages: 24

Brand: Morgan Pages: 4

Rota-Kit PRK-250

Brand: Audipack Pages: 46

Brand: Pyle Pages: 1

Brand: cecotec Pages: 92

Brand: SAPIRHOME Pages: 9

Brand: Zelmer Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands