ARM Cortex-A53 MPCore Technical Reference Manual Download Page 331

Page: 331 / 635

System Control

ARM DDI 0500D

4-270

ID021414

Non-Confidential

Table 4-244

shows the CPUACTLR bit assignments.

Table 4-244 CPUACTLR bit assignments

Bits

Name

Function

[63:31]

Reserved,

RES

[30]

FPDIDIS

Disable floating-point dual issue. The possible values are:

Enable dual issue of floating-point, Advanced SIMD and Cryptography instructions. This is
the reset value.

Disable dual issue of floating-point, Advanced SIMD and Cryptography instructions.

[29]

DIDIS

Disable Dual Issue. The possible values are:

Enable Dual Issue of instructions. This is the reset value.

Disable Dual Issue of all instructions.

[28:27]

RADIS

Write streaming no-allocate threshold. The possible values are:

0b00

16th consecutive streaming cache line does not allocate in the L1 or L2 cache.

0b01

128th consecutive streaming cache line does not allocate in the L1 or L2 cache. This is the
reset value.

0b10

512th consecutive streaming cache line does not allocate in the L1 or L2 cache.

0b11

Disables streaming. All write-allocate lines allocate in the L1 or L2 cache.

[26:25]

L1RADIS

Write streaming no-L1-allocate threshold. The possible values are:

0b00

4th consecutive streaming cache line does not allocate in the L1 cache. This is the reset value.

0b01

64th consecutive streaming cache line does not allocate in the L1 cache.

0b10

128th consecutive streaming cache line does not allocate in the L1 cache.

0b11

Disables streaming. All write-allocate lines allocate in the L1 cache.

[24]

DTAH

Disable Transient allocation hint. The possible values are:

Normal operation. This is the reset value.

The Transient allocation hint in the MAIR is ignored and treated the same as non-transient
allocation types. The

LDNP

and

STNP

instructions in AArch64 behave the same as the equivalent

LDP

and

STP

instructions.

[23]

STBPFRS

Disable ReadUnique request for prefetch streams initiated by STB accesses:

ReadUnique used for prefetch streams initiated from STB accesses. This is the reset value.

ReadShared used for prefetch streams initiated from STB accesses.

Summary of Contents for Cortex-A53 MPCore
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Cortex-A53 MPCore

Reviews:

Related manuals for Cortex-A53 MPCore

Brands by name

Popular brands

ARM Cortex-A53 MPCore, Technical Reference Manual

Search results

Summary of Contents for Cortex-A53 MPCore

Reviews:

Related manuals for Cortex-A53 MPCore

Brands by name

Popular brands