ARM Cortex-A53 MPCore Technical Reference Manual Download Page 41 | Manualshive

Page: 41 / 635

background image

Functional Description

ARM DDI 0500D

Copyright © 2013-2014 ARM. All rights reserved.

2-18

ID021414

Non-Confidential

Table 2-5

describes the supported power domain states for individual cores. The power domain

state in each core is independent of all other cores.

You must follow the dynamic power management and powerup and powerdown sequences
described in the following sections. Any deviation from these sequences can lead to

UNPREDICTABLE

results.

The supported power modes are:
•

Normal state

.

•

Standby state

on page 2-19

.

•

Individual core shutdown mode

on page 2-21

.

•

Cluster shutdown mode without system driven L2 flush

on page 2-22

.

•

Cluster shutdown mode with system driven L2 flush

on page 2-23

.

•

Dormant mode

on page 2-24

.

•

Retention state

on page 2-25

.

Normal state

This is the normal mode of operation where all of the processor functionality is available. The
Cortex-A53 processor uses gated clocks and gates to disable inputs to unused functional blocks.
Only the logic in use to perform an operation consumes any dynamic power.

Table 2-4 Supported processor power states

Power domains

Description

PDCORTEXA53

PDL2

PDCPU<n>

Off

Off

Off

Cluster off - L2 RAMs and all cores are off.

Off

On/Ret

Off

L2 Dormant mode - L2 RAMs retained and all cores are off.

On

Ret

Off/Ret

a

L2 Retention - L2 RAMs retained and all cores either retained or turned off.

On

On See

Table 2-5

Cluster L2 RAM active - L2 RAM active and all cores are in either on, off or
retention state.

a. All cores in the cluster to be in WFE, WFI, retention or powered off.

Table 2-5 Supported core power states

Power domains

Description

PDCPU

PDADVSIMD

Off

Off

Core off.

On

On

Core on - Advanced SIMD and Floating-point on.

On

Ret

AdvSIMD retention - Advanced SIMD and Floating-point in retention.

Ret

Ret

Core retention - core logic and Advanced SIMD and Floating-point in retention.

«
...
39
40
41
42
43
...
»

Summary of Contents for Cortex-A53 MPCore




























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-A53 MPCore

Brand: Scarlett Pages: 24

Brand: ricoo Pages: 8

Brand: Datavideo Pages: 30

Brand: CYP Pages: 12

Brand: Sony Pages: 18

Brand: Sony Pages: 46

Brand: Sony Pages: 67

Brand: Sony Pages: 1228

Brand: camry Pages: 36

Brand: Waring Pages: 6

Brand: Hotpoint Ariston Pages: 64

Brand: H.Koenig Pages: 44

vario SHIFT-LEG ADAPTION

Brand: AVstumpfl Pages: 13

Brand: Elechomes Pages: 14

LA MOULINETTE FORCE DP790A27

Brand: Moulinex Pages: 25

Brand: Galaxy Audio Pages: 40

Brand: NASA electric Pages: 17

Brand: iCES Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands