ARM Cortex-A53 MPCore Technical Reference Manual Download Page 172 | Manualshive

Page: 172 / 635

background image

System Control

ARM DDI 0500D

Copyright © 2013-2014 ARM. All rights reserved.

4-111

ID021414

Non-Confidential

Table 4-101

shows the L2ACTLR_EL1 bit assignments.

To access the L2ACTLR_EL1:

MRS Rt, S3_1_C15_C0_0; Read L2ACTLR_EL1 into Rt
MSR S3_1_C15_C0_0, Rt; Write Rt to L2ACTLR_EL1

4.3.67

Fault Address Register, EL3

The FAR_EL3 characteristics are:

Purpose

Holds the faulting Virtual Address for all synchronous instruction or data
aborts, or exceptions from a misaligned PC, taken to EL3.

Usage constraints

This register is accessible as follows:

Configurations

There is no additional configuration data for FAR_EL3.

Attributes

FAR_EL3 is a 64-bit register.

Figure 4-61 on page 4-112

shows the FAR_EL3 bit assignments.

Table 4-101 L2ACTLR_EL1 bit assignments

Bits

Name

Function

[31:30]

-

L2 victim Control.

0b10

This is the default value. Software must not change it.

[29:15]

-

Reserved,

RES

0.

[14]

Enable UniqueClean
evictions with data

Enables sending of WriteEvict transactions for UniqueClean evictions with data.
WriteEvict transactions update downstream caches that are outside the cluster. Enable WriteEvict
transactions only if there is an L3 or system cache implemented in the system.
The possible values are:

0

Disables UniqueClean evictions with data. This is the reset value for ACE.

1

Enables UniqueClean evictions with data. This is the reset value for CHI.

Note

Some ACE interconnects might not support the WriteEvict transaction. You must not enable this
bit if your interconnect does not support WriteEvict transactions.

[13:4]

-

Reserved,

RES

0.

[3]

Disable clean/evict
push to external

Disables sending of Evict transactions for clean cache lines that are evicted from the processor.
This is required only if the external interconnect contains a snoop filter that requires notification
when the processor evicts the cache line. The possible values are:

0

Enables clean/evict to be pushed out to external. This is the reset value for ACE.

1

Disables clean/evict from being pushed to external. This is the reset value for CHI.

[2:0]

-

Reserved,

RES

0.

EL0

EL1
(NS)

EL1
(S)

EL2

EL3
(SCR.NS = 1)

EL3
(SCR.NS = 0)

-

-

-

-

RW

RW

«
...
170
171
172
173
174
...
»

Summary of Contents for Cortex-A53 MPCore




























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-A53 MPCore

Kinetix Wizz BFP450

Brand: Breville Pages: 44

Brand: Barco Pages: 11

CUISINERY MM 8050

Brand: Grundig Pages: 1

Brand: Grundig Pages: 16

Brand: Grundig Pages: 11

Brand: Grundig Pages: 88

Brand: Cornell Pages: 7

70590 - Big Mouth 14 Cup Food Processor

Brand: Hamilton Beach Pages: 36

INFLATABLE SCREEN

Brand: DeeJay's Event Rentals Pages: 8

Brand: WMF Pages: 35

Brand: Qomo Pages: 11

Brand: Kalorik Pages: 80

Brand: QSC Pages: 28

Brand: Kasanova Pages: 58

Brand: TC Electronic Pages: 61

Brand: Menuett Pages: 36

Brand: Vitek Pages: 32

Peregrine HD 2 series

Brand: EPV Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands