ARM Cortex-A53 MPCore Technical Reference Manual Download Page 329

Page: 329 / 635

System Control

ARM DDI 0500D

4-268

ID021414

Non-Confidential

Ensure that the system has no outstanding ACP requests to the
Cortex-A53 processor.

When the L2 is idle, the processor can update the L2ACTLR followed by
an

ISB

. After the L2ACTLR is updated, the MMUs can be enabled and

normal ACE and ACP traffic can resume.

Configurations

There is one copy of this register that is used in both Secure and
Non-secure states.
L2ACTLR is mapped to the AArch64 L2ACTLR_EL1 register. See

Auxiliary Control Register

on page 4-109

Attributes

L2ACTLR is a 32 bit register.

Figure 4-139

shows the L2ACTLR bit assignments.

Figure 4-139 L2ACTLR bit assignments

Table 4-243

shows the L2ACTLR bit assignments.

To access the L2ACTLR:

MRC p15, 1, <Rt>, c15, c0, 0; Read L2ACTLR into Rt
MCR p15, 1, <Rt>, c15, c0, 0; Write Rt to L2ACTLR

31 30 29

15 14 13

4 3 2

RES

Disable clean/evict push to external

Enable UniqueClean evictions with data

L2 Victim Control

RES

Table 4-243 L2ACTLR bit assignments

Bits

Name

Function

[31:30]

L2 victim Control.

0b10

This is the default value. Software must not change it.

[29:15]

Reserved,

RES

[14]

Enable UniqueClean evictions with data

Enables UniqueClean evictions with data. The possible values are:

Disables UniqueClean evictions with data. This is the
reset value for ACE.

Enables UniqueClean evictions with data. This is the
reset value for CHI.

[13:4]

Reserved,

RES

[3]

Disable clean/evict push to external

Disables clean/evict push to external. The possible values are:

Enables clean/evict to be pushed out to external. This is
the reset value for ACE.

Disables clean/evict from being pushed to external. This
is the reset value for CHI.

[2:0]

Reserved,

RES

Summary of Contents for Cortex-A53 MPCore
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Cortex-A53 MPCore

Reviews:

Related manuals for Cortex-A53 MPCore

Brands by name

Popular brands

ARM Cortex-A53 MPCore, Technical Reference Manual

Search results

Summary of Contents for Cortex-A53 MPCore

Reviews:

Related manuals for Cortex-A53 MPCore

Brands by name

Popular brands