Applied Biosystems 7300 Installation And Maintenance Manual Download Page 12

Page: 12 / 174

Preface

How to Obtain More Information

xii

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

IMPORTANT!

– Provides information that is necessary for proper instrument operation,

accurate chemistry kit use, or safe use of a chemical.

Examples of the user attention words appear below:

Note:

Reset the Exposure Time to 2048 before performing the calibration for each filter.

IMPORTANT!

Wear powder-free gloves when you handle the halogen lamp.

Safety Alert

Words

Safety alert words also appear in user documentation. For more information, see

“Safety

Alert Words” on page xvi

How to Obtain More Information

Related

Documentation

For more information about using the 7300/7500/7500 Fast system, refer to the
documents shown below.

Portable document format (PDF) versions of this guide and most of the documentation
listed above are available on the SDS software installation CD.

Note:

For additional documentation, see

“How to Obtain Support”

page xiii

Send Us Your

Comments

Applied Biosystems welcomes your comments and suggestions for improving its user
documents. You can e-mail your comments to:

[email protected]

Document Title

Online Help

P/N

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System
Plus/Minus Detection Getting Started Guide

4347821

4378652

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System
Allelic Discrimination Getting Started Guide

4347822

4378653

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System
Relative Quantification Getting Started Guide

4347824

4378655

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System
Absolute Quantification Getting Started Guide

4347825

4378656

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System
Site Preparation Guide

4347823

4378654

Real-Time PCR Systems Chemistry Guide

4348358

4378658

Applied Biosystems 7500 FAST Real-Time PCR System,

QRC

4362285

4378659

Applied Biosystems Real-Time System Computer Set Up Guide,
QRC

4365367

4378660

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands