Applied Biosystems 7300 Installation And Maintenance Manual Download Page 123

Page: 123 / 174

Chapter 7

Verifying the Instrument Performance

Analyzing the TaqMan

RNase P Plate Data

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

12.

Calculate the verification value for the
5000-copy population:

In the Report tab, scroll to a sample in the
5K population.

Apply the values in the Mean Qty and
StdDev Qty columns to the following
equation:
5K value = Mean Qty + 3(StdDev Qty)

13.

Calculate the verification value for the
10000-copy population:

In the Report tab, scroll to a sample in the
10K population.

Apply the values in the Mean Qty and
StdDev Qty columns to the following
equation:
10K value = Mean Qty – 3(StdDev Qty)

14.

Compare the verification values for the 10000-
and 5000-copy populations:

• If the 10K value (

step 13

) is greater than the

5K value (

step 12

), the 7300/7500/7500

Fast system has passed the installation
verification.

• If the 10K value is not greater than the 5K,

the 7300/7500/7500 Fast system has failed
the installation verification. Troubleshoot
the RNase P verification run. See

“Troubleshooting” on page 99

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands