Applied Biosystems 7300 Installation And Maintenance Manual Download Page 20

Page: 20 / 174

Safety and EMC Compliance Information

General Instrument Safety

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

General Instrument Safety

PHYSICAL INJURY HAZARD.

Use this product only as

specified in this document. Using this instrument in a manner not specified by

Applied Biosystems may result in personal injury or damage to the instrument.

Moving and

Lifting the

Instrument

PHYSICAL INJURY HAZARD.

The instrument is to be moved

and positioned only by the personnel or vendor specified in the applicable site

preparation guide. If you decide to lift or move the instrument after it has been installed,

do not attempt to lift or move the instrument without the assistance of others, the use of

appropriate moving equipment, and proper lifting techniques. Improper lifting can cause

painful and permanent back injury. Depending on the weight, moving or lifting an

instrument may require two or more persons.

Moving and

Lifting Stand-

Alone Computers

and Monitors

Do not attempt to lift or move the computer or the monitor without

the assistance of others. Depending on the weight of the computer and/or the monitor,

moving them may require two or more people.

Things to consider before lifting the computer and/or the monitor:

• Make sure that you have a secure, comfortable grip on the computer or the monitor

when lifting.

• Make sure that the path from where the object is to where it is being moved is clear

of obstructions.

• Do not lift an object and twist your torso at the same time.
• Keep your spine in a good neutral position while lifting with your legs.
• Participants should coordinate lift and move intentions with each other before

lifting and carrying.

• Instead of lifting the object from the packing box, carefully tilt the box on its side

and hold it stationary while someone slides the contents out of the box.

Operating the

Instrument

Ensure that anyone who operates the instrument has:

• Received instructions in both general safety practices for laboratories and specific

safety practices for the instrument.

• Read and understood all applicable Material Safety Data Sheets (MSDSs). See

“About MSDSs”

page xxi

PHYSICAL INJURY HAZARD.

Use this instrument as specified

by Applied Biosystems. Using this instrument in a manner not specified by

Applied Biosystems may result in personal injury or damage to the instrument.

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands