Applied Biosystems 7300 Installation And Maintenance Manual Download Page 32

Page: 32 / 174

Chapter 1

Before Starting the Installation

Planning the Installation

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

~ 02:00:00

7300/7500

Perform the pure dye calibration

(Chapter 6):

a. Prepare the

pure dye

plates.

b. Create a plate document.

c. Perform the

pure dye

calibration.

d. Analyze the pure dye calibration data.

e. Evaluate pure dye calibration spectra.

~ 01:20:00

~ 01:00:00

Verify instrument performance

(Chapter 7):

a. Prepare the TaqMan

RNase P verification plate.

b. Create a plate document.

c. Perform the

verification run

d. Analyze the TaqMan

RNase P plate data.

7500 Fast

~ 00:40:00

7500/7500 Fast

7300

Note: You must be present at the instrument for approximately 5 minutes of the total run time.

7500 Fast

Recommended Workflow (continued)

See Note below

Perform the optical calibration

(7500/7500 Fast systems only,

Chapter 5):

a. Create a plate document.

b. Perform the optical calibration.

c. Analyze the optical calibration data.

~ 00:10:00

Perform the background calibration

(Chapter 5):

a. Prepare the

background

calibration plate.

b. Create a plate document.

c. Perform the background calibration.

d. Analyze the background data.

~ 00:30:00

Time Required

Task

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands