manualshive.com logo in svg

Applied Biosystems 7300, Installation And Maintenance Manual

Share
Download
Applied Biosystems 7300 Installation And Maintenance Manual Download Page 150

Appendix A

Updating the Operating System Software and Service Packs

124

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

Updating the Operating System Software and Service Packs

Do not upgrade the operating system of the computer connected to the 7300/7500/7500 
Fast system unless instructed to do so by an Applied Biosystems representative. New 
versions of the Microsoft Windows operating system can conflict with the SDS software 
and make the instrument inoperable. 

Service Pack

Updates

To install a service pack to update the operating system, review the release notes 
provided with the SDS software installation for compatibility issues.

Note:

Applied Biosystems service engineers maintain the operating system software as 

part of planned maintenance visits. During a visit, an engineer updates the computer 

operating system as upgrades become available and are validated by Applied 

Biosystems.

Summary of Contents for 7300















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands